This is the Highly Detailed factory service repair manual for the2005 HONDA ACCORD, this Service Manual has detailed illustrations as well as step by step instructions,It is 100 percents complete and intact. They are specifically written for the do-it-yourself-er as well as the experienced mechanic.2005 HONDA ACCORD Service Repair Workshop Manual provides step-by-step instructions based on the complete dis-assembly of the machine. It is this level of detail, along with hundreds of photos and illustrations, that guide the reader through each service and repair procedure. Complete download comes in pdf format which can work under all PC based windows operating system and Mac also, All pages are printable.

1. 2005 Honda Accord Service Manual
2. 2005 Honda Accord Owners Manual
3. 2005 Honda Accord Manual Book

Using this repair manual is an inexpensive way to keep your vehicle working properly. 2005 HONDA ACCORD Service Repair Manual. 1. 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord COMPONENT LOCATION INDEX Fig. 1: Locating SRS Components Courtesy of AMERICAN HONDA MOTOR CO., INC. 2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord 2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord me Tuesday, April 28, 2009 9:43:16 AM Page 1 2005 Mitchell Repair Information Company, LLC.

Me Tuesday, April 28, 2009 9:43:36 AM Page 1 2005 Mitchell Repair Information Company, LLC. 2: Locating SRS Components (4-Door Shown; 2-Door Similar) Courtesy of AMERICAN HONDA MOTOR CO., INC.

PRECAUTIONS AND PROCEDURES GENERAL PRECAUTIONS Please read the following precautions carefully before performing the airbag system service. Observe the instructions described in this information, or the airbags could accidentally deploy and cause damage or injuries. Except when performing electrical inspections, always turn the ignition switch OFF, disconnect the negative cable from the battery, and wait at least 3 minutes before beginning work. NOTE: The SRS memory is not erased even if the ignition 2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord me Tuesday, April 28, 2009 9:43:16 AM Page 2 2005 Mitchell Repair Information Company, LLC. Use replacement parts which are manufactured to the same standards and quality as the original parts.

Do not install used SRS parts. Use only new parts when making SRS repairs.

Carefully inspect any SRS part before you install it. Do not install any part that shows signs of being dropped or improperly handled, such as dents, cracks or deformation. 3: Inspecting SRS Parts Courtesy of AMERICAN HONDA MOTOR CO., INC. Before removing any of the SRS parts (including the disconnection of the connectors), always disconnect the SRS connector.

Switch is turned OFF or the battery cables are disconnected from the battery. 2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord me Tuesday, April 28, 2009 9:43:16 AM Page 3 2005 Mitchell Repair Information Company, LLC. Use only a digital multimeter to check the system. If it is not a Honda multimeter, make sure its output is 10 mA (0.01 A) or less when switched to the lowest value in the ohmmeter range.

A tester with a higher output could cause accidental deployment and possible injury. Do not put objects on the front passenger's airbag. The original radio and navigation system have a coded theft protection circuit.

Be sure to get the customer's anti-theft codes and write down the frequencies for the radio's preset stations before disconnecting the battery negative cable. Before returning the vehicle to the customer, enter the radio code, the navigation code, then enter the customer's audio presets, and set the clock. STEERING-RELATED PRECAUTIONS Cable Reel Alignment Misalignment of the cable reel could cause an open in the wiring, make the SRS system remote steering wheel controls and the horn inoperative. Center the cable reel whenever the following is performed (see step 6 in Installation ). Installation of the steering wheel - Installation of the cable reel - Installation of the steering column - Other steering-related adjustment or installation Do not disassemble the cable reel. Do not apply grease to the cable reel.

2005 Honda Accord Service Manual

If the cable, reel shows any signs of damage, replace it with a new one. For example, if it does not rotate smoothly, replace the cable reel. AIRBAG HANDLING AND STORAGE Do not disassemble an airbag.

It has no serviceable parts. Once an airbag has been deployed, it cannot be repaired or reused. For temporary storage of an airbag during service, observe the following precautions. 2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord me Tuesday, April 28, 2009 9:43:16 AM Page 4 2005 Mitchell Repair Information Company, LLC. Store the removed airbag with the pad surface up.

Never put anything on the airbag. 4: Storing Removed Airbag With Pad Surface Up Courtesy of AMERICAN HONDA MOTOR CO., INC. To prevent damage to the airbag, keep it away from any oil, grease, detergent, or water. 2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord me Tuesday, April 28, 2009 9:43:16 AM Page 5 2005 Mitchell Repair Information Company, LLC. 5: Keeping Airbag Away From Oil, Grease, Detergent Or Water Courtesy of AMERICAN HONDA MOTOR CO., INC.

Store the removed airbag on a secure, flat surface away from any high heat source (exceeding 200F/93C). 2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord me Tuesday, April 28, 2009 9:43:16 AM Page 6 2005 Mitchell Repair Information Company, LLC. 6: Removing Airbag Keeping Flat Surface Away From Any Heat Source Courtesy of AMERICAN HONDA MOTOR CO., INC. Never perform electrical inspections to the airbags, such as measuring resistance. Do not position yourself in front of the airbag during removal, inspection, or replacement. 2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord me Tuesday, April 28, 2009 9:43:16 AM Page 7 2005 Mitchell Repair Information Company, LLC. 7: Precaution For Airbag Removal, Inspection, Or Replacement Courtesy of AMERICAN HONDA MOTOR CO., INC.

Refer to the scrapping procedures for disposal of a damaged airbag. The side curtain airbag inflator assembly is a long, jointed part containing an inflator (A), a flexible bag (B), an adapter pipe (C), and a center bracket (D). 2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord me Tuesday, April 28, 2009 9:43:16 AM Page 8 2005 Mitchell Repair Information Company, LLC. 8: Identifying Side Curtain Airbag Inflator Assembly Components Courtesy of AMERICAN HONDA MOTOR CO., INC.

When removing or installing the side curtain airbag inflator assembly, never handle the flexible bag (B) or the adapter pipe (C). SRS UNIT, FRONT IMPACT SENSORS, SIDE IMPACT SENSORS, FRONT PASSENGER'S WEIGHT SENSOR UNIT ('04-05 MODELS), AND FRONT PASSENGER'S WEIGHT SENSORS ('04- 07 MODELS) Be careful not to bump or impact the SRS unit, front impact sensors, or side impact sensors when the ignition switch is ON (II), or for at least 3 minutes after the ignition switch is turned OFF. During installation or replacement, be careful not to bump (by impact wrench, hammer, etc.) the area around the SRS unit, front impact sensors, or side 2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord me Tuesday, April 28, 2009 9:43:16 AM Page 9 2005 Mitchell Repair Information Company, LLC. impact sensors. The airbags could accidentally deploy and cause damage or injury. 9: Precaution For Bump Area Around SRS Unit, Front Impact Sensors, Or Side Impact Sensors Courtesy of AMERICAN HONDA MOTOR CO., INC. 2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord me Tuesday, April 28, 2009 9:43:16 AM Page 10 2005 Mitchell Repair Information Company, LLC.

After a collision in which the front airbags or seat belt tensioners were deployed, replace the SRS unit, front sensors, and other related components (see COMPONENT REPLACEMENT/INSPECTION AFTER DEPLOYMENT ). After a collision in which a side airbag was deployed, replace the side impact sensor on the deployed side, and the SRS unit. After a collision in which the airbags or the side airbags did not deploy, inspect for any damage or any deformation on the SRS unit, front impact sensors, and side impact sensors. Replace all damaged parts. 10: Precaution For Deformation On SRS Unit Courtesy of AMERICAN HONDA MOTOR CO., INC. Do not disassemble the SRS unit, front impact sensors, side impact sensors, driver's seat position sensor, front passenger's weight sensor unit ('03-05 models), and front passenger's weight sensors.

Turn the ignition switch OFF, disconnect the battery negative cable, and wait at least 3 minutes before beginning installation or replacement of the SRS unit 2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord me Tuesday, April 28, 2009 9:43:16 AM Page 11 2005 Mitchell Repair Information Company, LLC. or disconnecting the connectors from the SRS unit. Be sure the SRS unit, front impact sensors, and side impact sensors are installed securely with the mounting bolts torqued to 9.8 N.m (1.0 kgf.m, 7.2 lbf.ft) Do not spill water or oil on the SRS unit or the side impact sensors, and keep them away from dust. Store the SRS unit, front impact sensors, and side impact sensors in a cool (less than 104 F/40 C) and dry (less than 80% relative humidity, no moisture) area. WIRING PRECAUTIONS Some of the SRS wiring can be identified by special yellow outer covering, and the SRS connectors can be identified by their yellow color. Observe the instructions.

Never attempt to modify, splice, or repair SRS wiring. If there is an open or damage in SRS wiring or terminals, replace the harness.

Owners manual 2015 honda aquatrax coast cycle world gulfport mississippi atv dealer coast cycle world ccw is tearing up your ecms by jumping them off ccw did. Related book ebook pdf 2015 honda aquatrax f 12x owners manual mercury marine service manual pdf mercury marine service manual 4 cyl inboard. Manual can be very useful guide the 2015 f12x and f12 turbo non turbo 2015 honda pwc aquatrax repair manual documents honda aquatrax service manual 2015. 2015 honda aquatrax f 12 x manual repair document for 2015 honda aquatrax f 12 x manual repair is available in various format such as pdf doc and epub which you can.

2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord me Tuesday, April 28, 2009 9:43:16 AM Page 12 2005 Mitchell Repair Information Company, LLC. 11: Never Attempt To Modify, Splice Or Repair SRS Wiring Courtesy of AMERICAN HONDA MOTOR CO., INC. Be sure to install the harness wires so they do not get pinched or interfere with other parts.

12: Do Not Pinch Or Interfere With Other Parts When Installing Harness Wires Courtesy of AMERICAN HONDA MOTOR CO., INC. Make sure all SRS ground locations are clean and securely fastened for optimum metal-to-metal contact. Poor grounding can cause intermittent problems that are difficult to diagnose. 2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord me Tuesday, April 28, 2009 9:43:16 AM Page 13 2005 Mitchell Repair Information Company, LLC.

PRECAUTIONS FOR ELECTRICAL INSPECTIONS When using electrical test equipment, insert the probe of the tester into the wire side of the connector. Do not insert the probe of the tester into the terminal side of the connector, and do not tamper with the connector. 13: Do Not Insert Probe Of Tester Into Terminal Side Of Connector 2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord me Tuesday, April 28, 2009 9:43:16 AM Page 14 2005 Mitchell Repair Information Company, LLC. Courtesy of AMERICAN HONDA MOTOR CO., INC. Use a U-shaped probe.

Do not insert the probe forcibly. 14: Using U-Shaped Probe Courtesy of AMERICAN HONDA MOTOR CO., INC. Use specified service connectors in troubleshooting.

Using improper tools could cause an error in inspection due to poor metal-to-metal contact. SPRING-LOADED LOCK CONNECTOR Some SRS system connectors have a spring-loaded lock. Front Airbag Connectors Disconnecting 2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord me Tuesday, April 28, 2009 9:43:16 AM Page 15 2005 Mitchell Repair Information Company, LLC. To release the lock, pull the spring-loaded sleeve (A) toward the stop (B) while holding the opposite half of the connector. Then pull the connector halves apart. Be sure to pull on the sleeve and not on the connector. 15: Disconnecting Front Airbag Connectors Courtesy of AMERICAN HONDA MOTOR CO., INC.

Connecting 1. To reconnect, hold the pawl-side connector, and press on the back of the 2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord me Tuesday, April 28, 2009 9:43:16 AM Page 16 2005 Mitchell Repair Information Company, LLC. sleeve-side connector in the direction shown in Fig. As the two connector halves are pressed together, the sleeve (A) is pushed back by the pawl (C).

Do not touch the sleeve. 16: Holding Pawl-Side Connector And Pressing On Back Of Sleeve- Side Connector Courtesy of AMERICAN HONDA MOTOR CO., INC. When the connector halves are completely connected, the pawl is released, and the spring-loaded sleeve locks the connector. 2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord me Tuesday, April 28, 2009 9:43:16 AM Page 17 2005 Mitchell Repair Information Company, LLC. 17: When Connector Is Connected Pawl Is Released And Spring- Loaded Sleeve Locks Connector Courtesy of AMERICAN HONDA MOTOR CO., INC.

Side Airbag Connector Disconnecting To release the lock, pull the spring-loaded sleeve (A) and the slider (B) while holding the opposite half of the connector. Then pull the connector halves apart. Be sure to pull on the sleeve and not on the connector half. 2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord me Tuesday, April 28, 2009 9:43:16 AM Page 18 2005 Mitchell Repair Information Company, LLC. 18: Disconnecting Side Airbag Connector Courtesy of AMERICAN HONDA MOTOR CO., INC.

Connecting Hold both connector halves, and press them firmly together until the projection (C) of the sleeve-side connector clicks. 2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord me Tuesday, April 28, 2009 9:43:16 AM Page 19 2005 Mitchell Repair Information Company, LLC. 19: Connecting Side Airbag Connector Courtesy of AMERICAN HONDA MOTOR CO., INC. REOPENING THE SRS UNIT CIRCUIT FOR DIAGNOSIS When SRS unit connectors A, B, or C are disconnected, a short circuit is created in NOTE: To prevent damage of the connector cavity, insert the SRS short canceller straight into the cavity from the terminal side. Do not use the special tool if it is damaged. Make sure to remove the special tool before reconnecting.

2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord me Tuesday, April 28, 2009 9:43:16 AM Page 20 2005 Mitchell Repair Information Company, LLC. the connector by its own function to prevent airbag deployment.

The circuit may need to be opened when diagnosis is performed on the circuit. Insert the SRS short canceller (No.

070AZ-SAA0100, short canceller) in the specified cavities when it is necessary to keep the circuit open for diagnosis. 2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord me Tuesday, April 28, 2009 9:43:16 AM Page 21 2005 Mitchell Repair Information Company, LLC. 20: Inserting SRS Short Canceller In Specified Cavities Courtesy of AMERICAN HONDA MOTOR CO., INC. 2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord me Tuesday, April 28, 2009 9:43:16 AM Page 22 2005 Mitchell Repair Information Company, LLC. 21: Identifying SRS Unit Connector A 28P Courtesy of AMERICAN HONDA MOTOR CO., INC. 2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord me Tuesday, April 28, 2009 9:43:16 AM Page 23 2005 Mitchell Repair Information Company, LLC. 22: Identifying SRS Unit Connector B 28P Courtesy of AMERICAN HONDA MOTOR CO., INC.

2005 Honda Accord Owners Manual

2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord me Tuesday, April 28, 2009 9:43:16 AM Page 24 2005 Mitchell Repair Information Company, LLC. 23: Identifying SRS Unit Connector C 16P Courtesy of AMERICAN HONDA MOTOR CO., INC. BACKPROBING SPRING-LOADED LOCK CONNECTORS When checking voltage or resistance on this type of connector the first time, you must remove the retainer to insert the tester probe from the wire side. 2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord me Tuesday, April 28, 2009 9:43:16 AM Page 25 2005 Mitchell Repair Information Company, LLC.

2005 Honda Accord Manual Book

To remove the retainer (A), insert a flat-tip screwdriver (B) between the connector body and the retainer, then carefully pry out the retainer. Take care not to break the connector. NOTE: It is not necessary to reinstall the removed retainer; the terminals will stay locked in the connector housing. 2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord me Tuesday, April 28, 2009 9:43:16 AM Page 26 2005 Mitchell Repair Information Company, LLC. 24: Removing Retainer Inserting Screwdriver Between Connector Body And Retainer Courtesy of AMERICAN HONDA MOTOR CO., INC. 2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord me Tuesday, April 28, 2009 9:43:16 AM Page 27 2005 Mitchell Repair Information Company, LLC.

SEATS WITH SIDE AIRBAGS Seats with side airbags have a 'SIDE AIRBAG' label on the seat-back. Because the component parts (seat-back cover, cushion, etc.) of seats with and without airbags are different, make sure you install only the correct replacement parts. 25: Identifying Side Airbag Label Courtesy of AMERICAN HONDA MOTOR CO., INC. When cleaning, do not saturate the seat with liquid, and do not spray steam on 2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord me Tuesday, April 28, 2009 9:43:16 AM Page 28 2005 Mitchell Repair Information Company, LLC. Do not repair a torn or frayed seat-back cover.

Replace the seat-back cover. After a collision in which the side airbag was deployed, replace the side airbag with new parts. If the seat-back cushion is split, it must be replaced. If the seat- back frame is deformed, it must be replaced. Never put aftermarket accessories on the seat (covers, pads, seat heaters, lights, etc.).

DISCONNECTING SYSTEM CONNECTORS Turn the ignition switch OFF and disconnect the negative cable from the battery, and wait at least 3 minutes before beginning the following procedures. Before disconnecting SRS unit connector B (3) from SRS unit, disconnect both seat belt tensioner 4P connectors (4, 5).

Before disconnecting the cable reel 4P connector (1), disconnect the driver's airbag 4P connector (2). 2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord me Tuesday, April 28, 2009 9:43:16 AM Page 29 2005 Mitchell Repair Information Company, LLC. 26: Disconnecting Negative Cable From Battery Courtesy of AMERICAN HONDA MOTOR CO., INC. 2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord me Tuesday, April 28, 2009 9:43:16 AM Page 30 2005 Mitchell Repair Information Company, LLC. Disconnect the battery negative cable, and wait at least 3 minutes.

Driver's Airbag 2. Remove the access panel (A) from the steering wheel, then disconnect the driver's airbag 4P connector (B) from the cable reel. 27: Removing Access Panel From Steering Wheel (Driver's Airbag) Courtesy of AMERICAN HONDA MOTOR CO., INC. 2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord me Tuesday, April 28, 2009 9:43:16 AM Page 31 2005 Mitchell Repair Information Company, LLC. Front Passenger's Airbag 3. Remove the glove box, then disconnect the front passenger's airbag 4P connector (A) from the dashboard wire harness.

28: Disconnecting Front Passenger's Airbag 4P Connector From Dashboard Wire Harness (Front Passenger's Airbag) Courtesy of AMERICAN HONDA MOTOR CO., INC. 2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord me Tuesday, April 28, 2009 9:43:16 AM Page 32 2005 Mitchell Repair Information Company, LLC. Side Airbag 4. Disconnect both side airbag 2P connectors (A) from the floor wire harness. 2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord me Tuesday, April 28, 2009 9:43:16 AM Page 33 2005 Mitchell Repair Information Company, LLC. 2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord me Tuesday, April 28, 2009 9:43:16 AM Page 34 2005 Mitchell Repair Information Company, LLC.

29: Disconnecting Side Airbag 2P Connectors From Floor Wire Harness (Side Airbag) Courtesy of AMERICAN HONDA MOTOR CO., INC. Side Curtain Airbag 5. Remove the headliner (see HEADLINER REMOVAL/INSTALLATION ). Remove the antenna coil (see WINDOW ANTENNA COIL REPLACEMENT ). Disconnect both side curtain airbag subharness 2P connectors from the side curtain airbags.

2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord me Tuesday, April 28, 2009 9:43:16 AM Page 35 2005 Mitchell Repair Information Company, LLC. 30: Disconnecting Side Curtain Airbag Subharness 2P Connectors From Side Curtain Airbags (Side Curtain Airbag) Courtesy of AMERICAN HONDA MOTOR CO., INC.

Seat Belt Tensioner 8. Remove the side trim panel. Remove the middle cross-member gusset. Disconnect both floor wire harness 4P connectors (A) from the seat belt 2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord me Tuesday, April 28, 2009 9:43:16 AM Page 36 2005 Mitchell Repair Information Company, LLC. tensioners. 31: Disconnecting Floor Wire Harness 4P Connectors From Seat Belt Tensioners (Seat Belt Tensioner) Courtesy of AMERICAN HONDA MOTOR CO., INC. 2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord me Tuesday, April 28, 2009 9:43:16 AM Page 37 2005 Mitchell Repair Information Company, LLC.

SRS Unit 11. Remove the center console and front panel. Remove the center console and front panel (see CENTER CONSOLE REMOVAL/INSTALLATION ). Remove the center pocket (see CENTER POCKET REMOVAL/INSTALLATION ).

Remove the center holder (see CENTER CONSOLE REMOVAL/INSTALLATION ). Remove the driver's and passenger's center lower cover (see DASHBOARD/STEERING HANGER BEAM REMOVAL/INSTALLATION ). Disconnect SRS unit connector A, and/or SRS unit connector B, and/or SRS unit connector C from the SRS unit.

2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord me Tuesday, April 28, 2009 9:43:16 AM Page 38 2005 Mitchell Repair Information Company, LLC. 32: Disconnecting SRS Unit Connector A, B And C From SRS Unit From SRS Unit (SRS Unit) Courtesy of AMERICAN HONDA MOTOR CO., INC.

GENERAL TROUBLESHOOTING INFORMATION DTC (DIAGNOSTIC TROUBLE CODES) The self-diagnostic function of the SRS system allows it to locate the causes of system problems and then store this information in memory. For easier troubleshooting, this data can be retrieved via a data link circuit. When you turn the ignition switch ON (II), the SRS indicator comes on.

If it 2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord me Tuesday, April 28, 2009 9:43:16 AM Page 39 2005 Mitchell Repair Information Company, LLC. goes off after 6 seconds, the system is normal, and is not currently detecting any abnormality. If there is an abnormality, the system locates and defines the problem, stores this information in memory, and turns the SRS indicator on.

The data will remain in the memory even when the ignition switch is turned off or if the battery is disconnected. The data is stored in memory as a diagnostic trouble code (DTC). DTCs are either latching or resetting depending on the malfunction. With resetting DTCs, the SRS indicator will go off the next time the ignition switch is turned ON and the system is normal, but the DTC is still stored. With latching DTCs the SRS indicator will not turn OFF until the malfunction is repaired and the DTC is cleared.

When you connect the HDS to the 16P data link connector (DLC), you can retrieve a more detailed DTC in the Honda Systems 'SRS' menu. After reading and recording the DTC, proceed with the troubleshooting procedure for that code. Precautions Use only a digital multimeter to check the system. If it's not a Honda multimeter, make sure its output is 10 mA (0.01 A) or less when switched to the smallest value in the ohmmeter range. A tester with a higher output could damage the airbag circuit or cause accidental airbag deployment and possible injury. Whenever the ignition switch is ON (II), or has been turned OFF for less than 3 minutes, be careful not to bump the SRS unit; the airbags could accidentally deploy and cause damage or injuries. Before you remove the SRS harness, disconnect the driver's airbag connector, the front passenger's airbag connector, both side airbag connectors, both side curtain airbag connectors, and both seat belt tensioner connectors.

Make sure the battery is sufficiently charged. If the battery is dead or low, measuring values won't be correct. Do not touch a tester probe to the terminals in the SRS unit or harness connectors, and do not connect the terminals with a jumper wire. Use only the 2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord me Tuesday, April 28, 2009 9:43:16 AM Page 40 2005 Mitchell Repair Information Company, LLC.

backprobe set and the HDS. Backprobe spring-loaded lock type connectors correctly. READING THE DTC HDS 1. Make sure the ignition switch is OFF. Connect the HDS to the DLC (A).

33: Connecting HDS To DLC Courtesy of AMERICAN HONDA MOTOR CO., INC. 2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord me Tuesday, April 28, 2009 9:43:16 AM Page 41 2005 Mitchell Repair Information Company, LLC. Turn the ignition switch ON (II). Use the HDS to check for DTCs. Read and record the DTC. Turn the ignition switch OFF, and wait for 10 seconds.

Disconnect the HDS from the DLC. Do the troubleshooting procedure for the DTC. ERASING THE DTC MEMORY WITH HDS 1. Make sure the ignition switch is OFF. Connect the HDS to the DLC (A).

2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord me Tuesday, April 28, 2009 9:43:16 AM Page 42 2005 Mitchell Repair Information Company, LLC. 34: Connecting HDS To DLC Courtesy of AMERICAN HONDA MOTOR CO., INC.

Turn the ignition switch ON (II). In the TEST MODE MENU of the HDS, select DTC CLEAR. This erases the DTC(s). Turn the ignition switch OFF, and wait for 10 seconds. Disconnect the HDS from the DLC. ERASING THE DTC MEMORY WITH MANUAL MODE Special Tools Required 2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord me Tuesday, April 28, 2009 9:43:16 AM Page 43 2005 Mitchell Repair Information Company, LLC. SCS Service Connector 07PAZ-0010100 To erase the DTC(s) from the SRS unit, use the HDS, or the following procedure.

Make sure the ignition switch is OFF. Connect the SCS service connector (A) to the yellow MES 2P connector (B).

Do not use a jumper wire. 2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord me Tuesday, April 28, 2009 9:43:16 AM Page 44 2005 Mitchell Repair Information Company, LLC.

35: Connecting SCS Service Connector To Yellow MES 2P Connector Courtesy of AMERICAN HONDA MOTOR CO., INC. Turn the ignition switch ON (II). The SRS indicator comes on for about 6 seconds, and then goes off. Remove the SCS service connector from the MES connector (2P) within 4 seconds after the indicator goes off. The SRS indicator comes on again. Reconnect the SCS service connector to the MES connector (2P) within 4 seconds after the indicator comes on. When the SRS indicator goes off, remove the SCS service connector from the MES connector (2P) within 4 seconds.

The SRS indicator blinks two times indicating that the memory has been erased. Turn the ignition switch OFF, and wait for 10 seconds. Turn the ignition switch ON (II) again. If the SRS indicator comes on for 6 seconds, and then goes off, the system is OK. INITIALIZING THE OPDS/ODS UNIT When a seat-back cover, seat-back cushion, and/or OPDS/ODS unit is replaced, initialize the OPDS/ODS by following the procedure. Erase the DTC memory (see 'ERASING THE DTC MEMORY WITH HDS').

Make sure the front passenger's seat is dry. Set the seat-back in a normal position, and make sure there is nothing on the seat. Make sure the ignition switch is OFF and the MES connector is not shorted. Connect the HDS to the DLC (A). NOTE: A new (uninitialized) OPDS/ODS unit installed with a faulty OPDS sensor can cause DTC 85-71. 2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord me Tuesday, April 28, 2009 9:43:16 AM Page 45 2005 Mitchell Repair Information Company, LLC. 36: Connecting HDS To DLC Courtesy of AMERICAN HONDA MOTOR CO., INC.

Turn the ignition switch ON (II). From the HDS Main Menu, select SRS, then Misc Test, then Adjustments. In the Adjustment Menu, select OPDS/ODS INIT. Follow the screen prompts to initialize the OPDS/ODS.

Turn the ignition switch OFF. Disconnect the HDS from the DLC. NOTE: If the OPDS/ODS system fails to initialize after several 2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord me Tuesday, April 28, 2009 9:43:16 AM Page 46 2005 Mitchell Repair Information Company, LLC. TROUBLESHOOTING INTERMITTENT FAILURES If there was a malfunction, but it doesn't recur, it will be stored in the memory as an intermittent failure, and the SRS indicator may come on depending on the malfunction detected. After checking the DTC, troubleshoot as follows: 1. Read the DTC (see 'Reading the DTC').

Erase the DTC memory (see 'ERASING THE DTC MEMORY WITH HDS'). Set the parking brake, then start the engine, and let it idle. The SRS indicator comes on for about 6 seconds and then go off.

Shake the wire harness and the connectors, take a test drive (quick acceleration, quick braking, cornering), turn the steering wheel fully left and right, and hold it there for 5 to 10 seconds. If the problem recurs, the SRS indicator will come on.

If you can't duplicate the intermittent failure, the system is OK at this time. CALIBRATING THE FRONT PASSENGER'S WEIGHT SENSOR UNIT ('04-05 MODELS) OR CALIBRATE THE ODS UNIT ('06-07 MODEL) When the front passenger's weight sensors and/or weight sensor unit ('04-05 models) or calibrate the ODS unit ('06-07 model) is replaced, calibrate the weight sensor unit ('04-05 models) or calibrate the ODS unit ('06-07 model) by following the procedure. While calibrating the front passenger's weight sensor unit ('04-05 models) or calibrate the ODS unit ('06-07 model), observe these precautions: Make sure all components of the front passenger's seat are correctly installed. Make sure all optional parts such as seat covers are removed. Attempts, replace the OPDS sensor and retry. If the OPDS/ODS system continues to fail to initialize, replace the OPDS/ODS unit.

2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord me Tuesday, April 28, 2009 9:43:16 AM Page 47 2005 Mitchell Repair Information Company, LLC. Make sure nothing is on or under the front passenger's seat. Make sure there is nothing in the front passenger's seat-back pocket. Keep the windows closed. Perform all calibration procedures except test driving in the service bay. Make sure the vehicle is on level ground. Keep the A/C and the heater off.

Do not touch the front passenger's seat until you drive the vehicle. Do not expose the front passenger's seat to sudden temperature changes. Position the front passenger's seat to the rear most position, and adjust the recliner to the most forward position. Do not move from these positions. Connect the HDS to the data link connector (DLC) (A). 2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord me Tuesday, April 28, 2009 9:43:16 AM Page 48 2005 Mitchell Repair Information Company, LLC.

37: Connecting HDS To DLC Courtesy of AMERICAN HONDA MOTOR CO., INC. Drive the vehicle, and accelerate to 20 mph (36 km/h), then stop on level ground. From the Main Menu, select SRS, then Seat Weight Sensor, then Misc Test, then Adjustments. Select 'SWS INIT' in the Adjustment Menu and follow the prompts until the initialization operation has been completed. OPERATION CHECK OF THE FRONT PASSENGER'S WEIGHT SENSOR UNIT ('04-05 MODELS) OR OPERATE THE ODS UNIT ('06-07 MODEL) 2007 Honda Accord 2003-07 RESTRAINTS SRS (Supplemental Restraint System) - Accord me Tuesday, April 28, 2009 9:43:16 AM Page 49 2005 Mitchell Repair Information Company, LLC. Thank you very much for your reading. Please Click Here Then Get More Information.

AutoZone's selection of Accord performance alternators guarantees finding the right piece of equipment to meet your needs. A good alternator has an output of between 13.5 and 14.8 volts, which keeps your battery 100 percent charged and powers all of your Accord's accessories, such as the headlights, radio and power windows/locks. A worn-out alternator ruins a good battery if you don't replace it quickly.

Batteries are rechargeable only so many times before they lose their ability to hold a charge. Swap out your old alternator for a new Honda Accord alternator and take advantage of AutoZone's Same-Day Store Pick-up if you need your aftermarket part right away.